JEE Advanced · Physics

Experimental Skills PYQs

6 previous-year questions from Experimental Skills in JEE Advanced, 2009–2026, latest first.

Q1JEE Advanced · 17 May 2026 · Paper-2Numerical answer
Two thin wires, Wire-1 of diameter 0.650 mm and Wire-2 of unknown diameter d are given. To obtain the value of d, the diameters of the two wires are measured with a screw gauge. The screw gauge has a pitch of 0.5 mm and there are 100 divisions on the circular scale (CS). The smallest division on the linear scale (LS) is 0.5 mm. The table shows the readings of LS and CS for the measurements. The value of d (in μm) is
LS (mm)
CS
Wire-1
0.5
42
Wire-2
1.5
95
Show answer & solution

Answer: 1915

LC = 0.005 mm; Wire-1 reads 0.5 + 0.21 = 0.71 mm vs true 0.65 ⇒⇒\Rightarrow zero error +0.06 mm Wire-2 reads 1.5 + 0.475 = 1.975 mm ⇒⇒\Rightarrow d = 1.915 mm = 1915 μm
Q2JEE Advanced · 22 May 2016 · Paper-2
There are two vernier calipers both of which have 1 cm divided into 10 equal divisions on the main scale. The Vernier scale of one of the calipers (C1) has 10 equal divisions that correspond to 9 main scale divisions. The Vernier scale of the other caliper (C2) has 10 equal divisions that correspond to 11 main scale divisions. The readings of the two calipers are shown in the figure. The measured values (in cm) by calipers C1 and C2, respectively, are figure
Question 2
  1. (A)2.87 and 2.86
  2. (B)2.87 and 2.87
  3. (C)2.87 and 2.83
  4. (D)2.85 and 2.82
Show answer & solution

Answer: C

C1: LC = 1 MSD − 1 VSD = 0.01 cm; reading = 2.8 + 7 ××\times 0.01 = 2.87 cm C2: 1 VSD = 1.1 MSD, so the vernier zero is behind the main scale mark; with the 7th vernier division coinciding, reading = 2.8 + (10 − 7) ××\times 0.01 = 2.83 cm
Q3JEE Advanced · 10 Apr 2011 · Paper-2
The density of a solid ball is to be determined in an experiment. The diameter of the ball is measured with a screw gauge, whose pitch is 0.5 mm and there are 50 divisions on the circular scale. The reading on the main scale is 2.5 mm and that on the circular scale is 20 divisions. If the measured mass of the ball has a relative error of 2 %, the relative percentage error in the density is
  1. (A)0.9 %
  2. (B)2.4 %
  3. (C)3.1 %
  4. (D)4.2 %
Show answer & solution

Answer: C

Least count = 0.5/50 = 0.01 mm; diameter = 2.5 + 20 ××\times 0.01 = 2.70 mm Δρρ=Δmm+3Δdd=2%+3×0.012.70×100%≈3.1%\frac{Δρ}{ρ} = \frac{Δm}{m} + 3\frac{Δd}{d} = 2\% + 3 \times \frac{0.01}{2.70} \times 100\% ≈ 3.1\%

3 more Experimental Skills questions

Practise them free

Practise all 6 Experimental Skills PYQs

Untimed with solutions, or as a timed test. Your mistakes are saved so you can retry them.

Start free